SERVICES

SERVICES

CUSTOM FABRICATION

Custom Stainless Steel Fabrication,
Custom Architectural Fabrication, Commercial/Residential/Industrial Custom, &
Interior Surface Fabrication.

WELDING

Custom Metal Fabrication, Sanitary Welding, & Custom Metal Finishing. We also offer mig, tig, and spot welding at very cost-effective rates.

WATER JET CUTTING 

One of the biggest advantages of water jet cutting is its inherent cold cutting quality. This allows materials to be cut that would be burned, melted, or cracked by other cutting methods. We can quickly produce large orders with ease and ensure they fit perfectly. 
Learn more below!

WATER JET CUTTING+

Water Jet cutting services for all materials. Whether you are cutting rubber, metals, plastics, wood, glass, mirrors, porcelain or composites, the abrasive Water Jet process will save you time and money for you and your company. Water Jet cutting is 5 to 10 times faster than wire EDM machining and with no significant induced heat from the process, Water Jet cutting provides unprecedented results over other cutting methods typically used. Water Jet cutting is superior to lasers and plasma for cutting reflective mediums and again with no heat stress.

Water Jet cutting tolerances are within .002 + or – and cutting speeds up to 10 times faster than a wire EDM. Five qualities of edge finish are attainable in most materials. Our 5-axis water jet is capable of producing the most precise, accurate cuts in a wide variety of materials. Thick metals even titanium and steel are no match for our 5-axis Water Jet; aluminum up to 12” in thickness and steel up to 9” in thickness can easily be processed by our equipment. Our system can also cut very thin materials with exceptional edge quality without risking structural damage.

In addition to providing the best quality cuts, our 5-axis Water Jet cutting system boasts a very high level of efficiency on many levels. Computer controlled nozzles eliminate the need for retooling between projects, saving you time and money.

This state-of-the-art-process can reduce your production times for rough outs and leave more time to complete the detailed finishing work. Going from prototype too small or medium production runs the same day are possible with this process. PPG abrasive Water Jet cutting service can process virtually any material quickly and leave a smooth finish that meets aerospace standards. Utilized in the production of components as thin as aerospace titanium to as thick as military armament, PPG can handle any production challenge.
Tolerances – +/- .002 within the cutting area
  • Cutting area of 48.5″ x 48.5″
  • Table Size 7’ 5” x 5’ 7”
  • All grades of Steel
  • Hardened Tool Steel
  • Glass and Mirrors
  • Optical quality glass
  • Composites
  • Ceramics and Porcelain
  • Copper
  • Inconel
  • Titanium
  • Rubber
  • Foam
  • Stone such as Marble, Granite & Limestone
  • Wood
  • Leather
  • Plastics such as Acrylic, Poly Carbonates
  • Mirrored Stainless Steel

Benefits of Abrasive Water Jet Cutting:
  • Water Jet Cutting creates superior edge quality
  • Typical finishes 125-250 microns – Q1 through Q5
  • Dependent upon materials and thickness
  • Reduced need for secondary finishing
  • No cutter-induced distortion
  • Low cutting forces on work piece
  • Limited tooling requirements
  • Little to no cutting burr
  • Water Jet Cutting preserves metallurgical integrity
  • No heat-affected zone
  • Localizes structural changes
  • No cutter-induced metal contamination
  • Eliminates thermal distortion
  • Minimal delimitation of edge cut surfaces
  • No fraying of edge cut surfaces
  • No thermally induced cracking
  • No splintering
  • No slag or cutting dross
  • Precise multi-plane cutting of contours, shapes, and bevels of any angle
  • Water Jet Cutting can perform composite cutting – nonmetallic
  • Water Jet Cutting creates smooth cuts
  • Water Jet Cutting is Omni-directional

 

METAL FABRICATION+

As Kapolei's signature metal fabrication service, we go beyond simple welding with high pressure water cutting, professional assembly and always providing superior customer service. We'll ensure your project moves quickly from conception to final results and we're happy to oblige any special request. When you need metal fabrication you can count on there's no better choice than Pac Pro Hawaii.
There's no job that's too big or too small for us to handle. Whatever your project may be - we'll ensure we get it done for you on-time and on-budget. Call us now for more information!

WELDING+

Whether you need welding for a new development or spot welding for personal project - we can ensure the welds are done right. We offer custom welding and Water Jet cutting and fabrication at very competitive rates. We'll work within your timetable and keep in close communication during the process. Call us today to find out how we can best serve you!

No matter the scope for size of your project - we pride ourselves on our welding expertise. Our team can get the job done on-time and on-budget and we always stand behind our work. We also offer mig, tig and spot welding at very cost-effective rates. Call us today!
Share by: